| Part No | Produsent | Applikasjon |
|---|
| SI7661CJ | MaximIC | CMOS voltage converter |
| MAX779LC/D | MaximIC | Low-voltage input, step-up DC-DC converter |
| MAX763ACSA | MaximIC | Step-down, current-mode PWM DC-DC controller. Input voltage range 3.3V to 11V |
| ICL7631BCJE | MaximIC | Triple operational amplifier, 5mV |
| MAX3218C/D | MaximIC | 1.8V to 4.25V-powered, 1microA supply current RS-232 transceiver with AutoShutdown. |
| MAX551BEPA | MaximIC | +5V, 12-bit, serial, multiplying DAC. Linearity(LSB) +-1. |
| MAX807NEPE | MaximIC | Full-featured microprocessor supervisory circuit with +-1.5% reset accuracy. Reset threshold (typ) 4.575V |
| MAX4661CAE | MaximIC | 2.5om, quad, SWPST, CMOS analog switch (four NC switches). |
| MAX6322HPUK41A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1ms |
| MAX396EPI | MaximIC | Precision, 16-channel, low-voltage, CMOS analo0g multiplexer. |
| MAX232EJE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX3316EEAE | MaximIC | +-15kV ESD-protected, 2.5V, 1microA, 460kbps, RS-232 compatible transceiver. |
| MAX4668CPE | MaximIC | 2.5om, quad, SPST, CMOS analog switch (two NO switches). |
| MAX146BEPP | MaximIC | +2.7 V, low-power, 8-channel, serial 12-bit ADC. INL(LSB) +-1. |
| MAX6317HUK36AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX412ESA | MaximIC | Dual, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX6318LHUK40BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.000V min, reset timeout 20ms,typ watchdog timeout 1.6sec |
| MAX4426C/D | MaximIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX2235EUP | MaximIC | +3.6V, 1W autoramping power amplifier for 900MHz applications. |
| MAX6358TYUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 3.08V (Vcc5) and 2.19V (Vcc3). Active-low open-drain reset. Watchdog timer. |
| MAX6319LHUK48A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 1ms |
| MAX293C/D | MaximIC | 8th-order, lowpass, elliptic, switched-capacitor filter. Clock-tunable corner-freguency range 0.1Hz to 25kHz |
| MAX6343SUT-T | MaximIC | Microprocessor reset circuit with power-fail comparator. Reset threshold 2.93V. Open-drain active-low reset output, manual-reset input. |
| MAX6320PUK30AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| DG441DJ | MaximIC | Improved, quad, SPST analog switch |
| MAX513MJD | MaximIC | Low-cost, triple, 8-bit voltage-output DAC with serial interface. |
| DG306AC/D | MaximIC | CMOS dual and quad analog switch. |
| MAX6317HUK35BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX3181EUK-T | MaximIC | +3V to +5.5V, 1.5Mbps RS-232 receiver. |
| ICL8069DCZQ2 | MaximIC | Low-voltage reference, 100 ppm/C - max temp. coefficient. |
